Assembly

Shenzhen I/O – Passive Infrared Sensor

Shenzhen I/O – Passive Infrared Sensor

I think we are at problem number 7 in Shezhen I/O where we are asked to help a security company design a passive infrared sensor that will trigger an alarm between a given time interval, if there is too much activity. We are given a problem where were have the a simple sensor input and a simple alarm output. We also have a simple input giving us time. Further more we have 2 xbus inputs giving us the on and off times. The problem description is simple enough, if the timer is between the on and off time (loop) and the sensor reading is 20 or higher we should trigger the alarm. Just like the signals here tells us

Shenzhen IO - Passive Infrared Sensor - signals Continue reading →

Posted by Kristian in Shenzhen IO, 0 comments
Shenzhen I/O – Harmonic Maximization Engine

Shenzhen I/O – Harmonic Maximization Engine

By now we are veterans in making cheap electronic gadgets for the company. And now they want us to make a Harmonic Maximization Engine! That sounds cool.

When we look at the specifications we are supposed to copy the audio-in to audio out as long as the maximize is not high.

If the maximize input is high then we should apply the following algorithm

AUDIO_OUT = (AUDIO_IN – 50) x 4 + 50

As it is given to us in the manual. This gives us the following signals for verification

Shenzhen IO - harmonic maximization engine - signals Continue reading →

Posted by Kristian in Shenzhen IO, 0 comments
Shenzhen I/O – Drinking Game Scorekeeper

Shenzhen I/O – Drinking Game Scorekeeper

Joe have been out drinking again. This time with Baron Von Schnapps. I don’t say this was a serious game. However, it resulted in yet another deal for us. So good job Joe on landing electronics, bad job for your liver. However, they want to promote their drink with a small game. And we are to make a drinking Game Scorekeeper to help them with that.

He might not remember the exact rules, but we are given two inputs called point and foul. As well as a display with a non-blocking xbus input. And if they trigger point, we should increment the display with one. If we get a foul we should subtract 2. However, we should never show less than zero on the display. Continue reading →

Posted by Kristian in Shenzhen IO, 0 comments
Shenzhen I/O: Animated Esports Sign

Shenzhen I/O: Animated Esports Sign

I think Joe has been out drinking with some friends. At least he landed us the fourth deal. We are to make an animated esports sign for one of the famous stars in the world.

The board has 5 simple outputs and we are supposed to generate signals that looks like

Animated Esports Sign - signals Continue reading →

Posted by Kristian in Shenzhen IO, 0 comments
Shenzhen I/O: Diagnostic Pulse Generator

Shenzhen I/O: Diagnostic Pulse Generator

The third task we get is playing solitaire, but ignoring that the third programming puzzle we get is that we need to test some manufacturing equipment. We can do that by building a diagnostic pulse generator that sends a pulsing signal to the output whenever we hold a button.

The board looks like this where the button is a simple input. When it goes high we should generate a pulse to the pulse output with a certain characteristic. Continue reading →

Posted by Kristian in Shenzhen IO, 0 comments
Shenzhen I/O: Control Signal Amplifier

Shenzhen I/O: Control Signal Amplifier

In our second assignment we are asked to build a signal amplifier as a replacement for a control signal amplifier factory module that got eeeehhhh smashed…. but don’t worry, no one was hurt much. This task is in my opinion still as close as we get to a tutorial in this game as we ever will. The signal amplifier is pretty simple. We will take the input signal from a simple input, multiply it by 2 and send it to the simple output pin.

Continue reading →

Posted by Kristian in Shenzhen IO, 0 comments
Shenzhen I/O: Fake Surveillance Camera

Shenzhen I/O: Fake Surveillance Camera

The very first challenge we get in Shenzhen IO is to make some LEDs blink on a fake security camera. We have just been hired by Shenzhen Longteng Electronics CO. Ltd and we are taking on an old project we are taking over from a guy who quit. The camera has two LEDs called “active” and “network” and we should design and code the solution to make them blink in this pattern

Continue reading →

Posted by Kristian in Shenzhen IO, 0 comments